Configure the relationship of the two monitors to reflect the physical placement of both monitors with the new monitor 2 on the left as the main display. Configure the display properties to show the Start menu and taskbar on the left monitor. Make sure Extend these displays is selected. Connect the original monitor to the new video card using the DVI-D cable. The new monitor is already plugged into the surge protector. Connect the left monitor to the newly installed video card using an HDMI cable. When installing the video card, connect the PCIe power connector to the video card. In this lab, your task is to configure dual monitors as follows: Select and install a video card that provides you with dual monitor support for both monitors using a digital connection to the video card. ![]() The video card in the computer currently only supports a single monitor, so you will need to upgrade the video card to support dual monitors. You have purchased a second monitor and placed it in the Workspace (the monitor on the left). You need to upgrade the computer in Office 2 to support dual monitors. To make the system easier to use, she has requested dual monitors. The employee in Office 2 is setting up a virtualization environment for software development. You are the IT administrator for a small corporate network. From the Plugged in drop-down list, make sure Do nothing is selected. Form the On battery drop-down list, select Hibernate. Modify the Presentation power plan settings as follows: To the right of Presentation, select Change plan settings. From the Put the computer to sleep drop-down list, select Never for Plugged in. From the Put the computer to sleep drop-down list, select 2 hours for On battery. From the Turn off the display drop-down list, select Never for Plugged in. From the Turn off the display drop-down list, select 1 hour for On battery. In the Plan name field, enter Presentation. Under Related settings, select Additional power settings. From the left menu, select Power & sleep. The Status window shows an active connection to the network and the internet.Ĭreate a custom power plan as follows: Select Start. After the operating system loads, right-click the Network icon and select Open Network & Internet settings. Click the power button on the computer case to turn the computer on. Confirm that the computer is connected to the local network and the internet as follows: Above the computer, select Front to switch to the front view of the computer. In the Selected Component window, drag the other connector to the Ethernet port on the wall outlet. In the Selected Component window, drag a connector to the NIC port on the 1000BaseTX network adapter. PCIe Slot Connect the computer to the network as follows: Above the computer, select Back to switch to the back view of the computer. Drag the 1000BaseTX network adapter to a free PCIe slot on the computer. When the BIOS loading window appears, press F2 to enter the BIOS.Īctions you were required to perform: Install the 1000BaseTX network adapter in the Support workstation Connect the new NIC to the network using a Cat6a cable Verify that the Support workstation can communicate with the internet using the new NIC Above the computer, select Motherboard to switch to the motherboard view of the computer. On the computer, select the power button on the front of the computer. Boot into the BIOS and verify that all installed modules are recognized by the BIOS as follows: Above the computer, select Front to switch to the front view of the computer. Repeat steps 2b-2c until all memory slots in the computer are filled with good modules. If the memory tester indicates OK, the module is good drag the module to the computer. If the memory tester indicates BAD or ERROR, the module is bad return the module to the Shelf. Drag a memory module from the Shelf to the correct slot on the memory tester. Test and install the memory modules on the Shelf as follows: On the Shelf, expand Memory Modules. Repeat steps 1d-1e for all memory modules in the computer. ![]() If the memory tester indicates OK, the module is good. ![]() If the memory tester indicates BAD or ERROR, the module is bad. Drag a memory module from the computer to the correct slot on the memory tester. Drag the Memory Tester from the Shelf to the Workspace. Test the memory modules in the computer as follows: Above the computer, select Motherboard to switch to the motherboard view of the computer.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |